Get a Tap Installation; Faucets, Mixers & Outdoor Taps
Main Drain Mechanical handles everything from a single kitchen tap installation to multi-unit tap installation across a strata building, serving homeowners, strata managers, and general contractors across the Lower Mainland. Every tap installation service runs through a Red Seal plumber with full WorkSafeBC coverage and over 25 years of combined trade experience, the credentials cautious buyers check for before approving a vendor. Whether it’s an outdated fixture, a renovation upgrade, or a tenant complaint that needs a proper fix, this is who you call.
When a Tap Swap Turns Into Something More
You cleared out the cabinet, watched a YouTube video, and got as far as the shutoff valve; then discovered the fitting underneath is corroded solid, the supply lines are the wrong size for the new fixture, or the valve itself barely turns. What looked like a Saturday afternoon job is now a dripping, half-dismantled sink you can’t leave until Monday. And if the old lines go while you’re wrestling with them, you’re not dealing with a tap anymore, you’re dealing with water on the floor, a cabinet to dry out, and a repair bill that dwarfs whatever the installation would have cost.
The New Tap Gets Installed Once, And Stays That Way
Tap installation services means more than threading a new fixture onto an existing line. A properly done job involves shutting down the supply, removing the old compression fitting without damaging the seat or surrounding surfaces, inspecting the supply lines and shutoff valve while everything is open, fitting the new tap to manufacturer spec and BC Plumbing Code standard, and pressure-testing the connections before anything gets put back together. Main Drain Mechanical’s Red Seal-certified crew handles every one of those steps; so the result is a tap that holds pressure, doesn’t drip behind the cabinet, and is backed by a 1-year workmanship warranty on the installation itself.
How We Approach Every Faucet installation Job!
Each job gets the same structured attention, whether it’s a single kitchen or a strata building authorizing bathroom tap setup across multiple units:
- We assume the shutoff valve is the real risk, not the tap itself. A corroded valve or a failing braided supply line is often the actual problem hiding behind a worn fixture; we’d rather find that now than have it fail on its own later.
- Manufacturer spec and BC Plumbing Code aren’t optional extras. A tap installed to code is what protects landlords and strata managers from a liability issue down the line, not just what looks finished from the front.
- We don’t consider a connection tested until it’s under real pressure. A slow drip behind a closed cabinet does its damage quietly, so nothing gets closed up until water pressure at the fixture confirms it’s actually holding.
- Low flow gets traced to its cause, not shrugged off. A restricted aerator or a valve that isn’t fully open looks like a “normal” new-fixture quirk to most people, we check it before we call the job done, not after.
- The job isn’t finished until the space looks like we were never there. No tools left out, no cabinet doors open, no debris under the sink, that’s part of the work, not an afterthought.
Who We Serve?
How Our faucet installation Goes
From your first message to a tested, working fixture; here’s exactly what the process looks like on your end.
- You tell us what you need: A kitchen faucet installation, a mixer faucet installation, an outdoor faucet installation for a hose bib, or a bathroom fixture for a renovation, we ask about fixture type and whether it’s a rough-in or a straightforward replacement, so the right materials are already on the truck when we arrive.
- We shut off the water and drain the lines: The supply is shut down at the shutoff valve and the lines are drained before anything comes off the wall or out of the cabinet. If that valve hasn’t been turned in 15 years, we check it properly first — a valve that seizes mid-job turns a simple swap into a different job entirely.
- The old fixture comes out and gets inspected: This is where a rushed install or old DIY work usually shows itself, stripped threads, a mismatched compression fitting, or a corroded supply line one stress-point from failing. We document what we find and flag anything that needs attention before the new fixture goes in.
- The new tap goes in, fitted to standard: The replacement is installed to BC Plumbing Code, thread sealant applied correctly, supply lines torqued right. For mixer taps and pull-down faucet installation work specifically, we confirm the cartridge seats properly and the spray function operates before moving to the next step.
- We pressure-test, check everything, and clean up: Water goes back on and we run a pressure check at the fixture, checking the base, the supply connections, and the drain for any drip. Nothing gets signed off until it holds. The cabinet is left exactly as we found it, no tools left behind, no wet towel on the counter.
How Much Will it Cost You?
faucet setup pricing in the Lower Mainland follows a fairly predictable range, and knowing how it’s built helps you evaluate any quote fairly.
A basic single-fixture tap installation; kitchen tap installation or bathroom tap setup with functioning shutoff valves typically runs $150–$550 + GST. More involved jobs, like a new rough-in location, a mixer faucet setup, or a job where the supply lines and shutoff valves need replacing, generally run $400–$2,000+ + GST depending on scope.
The fastest way to get an accurate number is a quick call or message, we’ll give you an honest range before you commit to anything.